Why Adding More Powder Coating Makes Pinholes Worse (And What Actually Works)
A few years ago, a job shop running die-cast aluminum parts had a rejection rate hovering around 30% because of pinholes. The first instinct on the floor was predictable: spray a heavier coat. If the pinholes are breaking through the surface, put down more powder and bury them. That instinct is almost always wrong. On thick-film powder coatings, adding material does not hide the defect—it multiplies it.
The reason sits at the intersection of substrate chemistry and film physics, and understanding it changes how you approach every porous or outgassing-prone part that comes through the line.
Two different gases, one visible symptom
Pinholes in powder coating are circular micro-voids that break through the cured film. Under low magnification, they look like tiny concentric craters. What comes out of them is gas, but the gas does not always come from the same place.
The first source is the substrate itself. Castings, galvanized steel, laser-cut edges, welds, and poorly cleaned surfaces can hold trapped air, moisture, oils, or pretreatment chemistry below the surface. When the part enters the cure oven and heats up, those volatiles expand. The powder has already melted into a continuous film. The gas has nowhere to go but through that film, and it leaves a pinhole on the way out.
The second source is the powder itself. Even a perfectly clean substrate produces some gas during cure. Interstitial air between powder particles escapes as the particles coalesce. More importantly, some chemistries evolve volatiles as a byproduct of crosslinking. HAA-polyester systems release water during cure. Polyurethane systems release ε-caprolactam, a blocking agent. Formulators add degassing agents to usher these volatiles out before the film hardens, but degassing agents have a ceiling. Once the film passes roughly 5.0 mils (about 100 microns), cure volatiles alone can generate pinholing even when the substrate is spotless.
This distinction matters because the fixes are different. Substrate outgassing demands pretreatment and pre-baking. Cure-volatile pinholing demands film thickness discipline and, in some cases, a different powder chemistry. Treating one as the other wastes time and material.
The thick-film trap
Here is the counterintuitive part. When a film is thin, gas that evolves from the substrate or the powder has a short path to the surface. The film may still be fluid enough for the bubble to break and the coating to level back over the void. As the film gets thicker, three things happen at once.
The gas has farther to travel. The film skin sets faster on the outside while the interior remains molten. And the pressure inside the film increases because the gas is sealed under a heavier, increasingly crosslinked layer. The result is not a buried defect. It is a more violent escape. Powder coating technical sources are blunt about this: increasing film thickness to “bury” outgassing “only makes it worse by sealing gases in and increasing internal pressure during cure”.
The same logic applies to cure volatiles. A thick HAA film generates more water per unit area than a thin one, simply because there is more resin crosslinking. The film also has less time and less permeability to vent that water before gelation locks the surface. A recent patent filing from Valspar explicitly names this as a known limitation of HAA curing: thick coatings are prone to pinholes, and the industry has been searching for a low-temperature system that can run at 120 microns without them. When a patent has to claim “substantially free of pores” at 120 micrometers as a surprising result, it tells you how stubborn the thick-film pinhole problem is in HAA chemistry.
What the numbers look like on real parts
The gap between theory and shop-floor results is where this topic gets useful.
On die-cast aluminum, porosity is not an occasional anomaly. It is a structural feature of the casting process, and it often reaches the surface. Die lubricant residues can penetrate 50 to 200 micrometers into that surface porosity and begin volatilizing between 150°C and 250°C—right in the middle of the cure window. A pre-bake at 220–250°C for 20–45 minutes, depending on wall thickness, drives those volatiles off before powder ever touches the part. Shops that implement a proper degas bake report pinhole rejects dropping by 60 to 80 percent on castings with marginal porosity.
For galvanized steel, the mechanism is slightly different but the prescription is similar. Water can be entrained in the zinc layer during quenching, and pretreatment chemicals can lodge in the surface. Pre-baking at 20–30°F above the recommended cure temperature, long enough for the metal itself to reach that temperature, is the standard mitigation. The part should then cool to within 25°F of ambient before coating. Skipping the cool-down or trusting oven air temperature instead of part metal temperature is a common way to reintroduce the defect.
Formulation can help, but it is not a substitute for substrate control. Degassing additives in the 0.3–0.5% range have been shown to cut pinholes substantially in HAA systems at thicker film builds, and wax-based degassing agents create a soft, fluid pathway for gas to escape before the film hardens. But even the best degassing package operates within a thickness window. Push past that window, and the additive cannot outrun the physics.
A working sequence for thick-film parts
The practical takeaway is not “never spray thick.” Some specifications genuinely require high film build for corrosion or mechanical protection. The takeaway is that thick film must be earned through substrate discipline, not compensated for by extra powder.
Start with the part metal temperature question, not the powder. If the substrate is porous, cast, galvanized, or welded, a pre-bake is not optional. Set the pre-bake oven above the cure temperature and verify that the part itself reaches that temperature, not just the oven air. Cool the part before spraying.
Then control film thickness deliberately, especially on edges and complex geometry. Edges naturally draw more powder because of electrostatic field concentration, and they are also where outgassing defects concentrate. A film that measures 4.0 mils on a flat panel can easily hit 6.0 mils on an edge, which is precisely where cure volatiles and substrate gases have the hardest time escaping.
If the substrate cannot be fully degassed—some castings are simply too porous, and the caster’s process is outside your control—a powder formulated for outgassing forgiveness can buy margin. These products use longer flow times or venting chemistries to tolerate gas evolution that a standard powder would fail on. But they work best when the pre-bake has already done most of the heavy lifting.
The rejection rate on that die-cast job did not fall because the shop sprayed more powder. It fell when they stopped trying to cover the gas and started removing it before the powder went on. Thick film is a coating specification. Pinhole-free thick film is a process specification.

D5 Creation