Powder Coating News
now browsing by category
Hot news ,developing ,technology of powder coating industry .
Application of pearlescent paint in construction industry
With mechanicals of high decorative paint coating (high distinctness of image, high brightness, high flash colored) increasing demand, pearlescent paint has a pearl effect, flash effect and color varying with angles effect of metallic, its application gradually is increased. Different colors at different angles Metallic pigments and pearlescent pigments in the coating film alignment state a greater impact on the flop effect. That is at the same angle of incidence changes with the perspective of the viewer, the film’s intenseRead More …
Research and application of crack paint in construction machinery industry
Introduction to crack paint Crack Paint is an art paint, it is distinctly different colors with primer paint spraying cracks formed on the surface to be painted pattern uniform texture, varied, well-proportioned, very three-dimensional effect with a crack beauty named. Crack paint forming principle In the crack topcoat film forming process, since the rapid evaporation of the solvent, resulting in internal topcoat film cracks due to uneven force, showing a gap irregular crack, the crack so that a different colorRead More …
Attending 118th session of Canton Fair
The 118th session of Canton Fair will begin from Oct 15th,2015 at China Import and Export Fair Complex in Guangzhou. Jinhu Color Powder Coating will be at present on time. We are looking forward to your visit. Booth Number : 14.4L52-53 Area : Chemical Area Phase 1:Oct 15-19, 2015 China Import and Export Fair, also known as the Canton Fair, is held biannually in Guangzhou every spring and autumn, with a history of 58 years since 1957. The Fair isRead More …
Bend test – Qualicoat Testing
All organic coatings except class 2 and 3 powder coatings: EN ISO 1519 Class 2 and 3 powder coatings: EN ISO 1519 followed by a tape pull adhesion test as specified below: Apply an adhesive tape to the significant surface of the test panel following the mechanical deformation. Cover the area by pressing down firmly against the coating to eliminate voids or air pockets. Pull the tape off sharply at right angles to the plane of the panel after 1Read More …
Resistance to boiling water- Qualicoat Testing
Method 1 with boiling water: 2 hours immersion in boiling demineralised water (maximum 10 μS at 20°C). Remove the test sample and allow it to cool down to room temperature. Apply an adhesive tape (see § 2.4) to the surface, ensuring that no air is trapped. After one minute, remove the tape at an angle of 45° with a sharp even pull. Method 2 with a pressure cooker: (to be used for powder and electrophoretic coatings only) Add demineralised waterRead More …
Antique Red Gold/ YK-EPR378
Antique Red Gold Powder Paint Colors Code:YK-EPR378 Color: Red background with gold vein Chemistry System: Epoxy Polyester Gloss: High gloss Surface: Antique wrinkle vein Use : For indoor Application: Sprayed with electrostatic gun Coat layer: One coat layer SEND INQUIRY
Dark Green Hammer/ YK-EP8GH-H17
Dark Green Hammer Powder Paint Color Code:YK-EP8GH-H17 Color: Dark green,similar to RAL6005 Chemistry System: Epoxy Polyester Gloss: High gloss Surface: Hammer wrinkle vein Use : For indoor Application: Sprayed with electrostatic gun Coat layer: One coat layer SEND INQUIRY
Electrostatic Painting Process
Electrostatic painting is a process in which a spray gun tip is electrostatically charged; making the paint charged electrically; thereby allowing the paint to be attracted to a grounded surface. This process wastes almost no paint through normal air flow, wind, or dripping. This is because the paint particles are actually attracted to the surface you are painting like a magnet. However, in order for the process to work the object you are painting has to be grounded. Electrostatic sprayingRead More …
Accelerated weathering test for Qualicoat
EN ISO 11341 Luminous intensity: 550 ± 20 W/m2 (290 – 800 nm) Black standard temperature: 65 ± 5°C Demineralised water: maximum 10 μS Special UV filter (290 nm) Cycles of 18 minutes in a wet medium and 102 minutes in a dry medium. After 1000 hours exposure (2000 hours for class 3), the test panels should be rinsed with demineralised water and checked for: Gloss variation: EN ISO 2813 angle of incidence 60° Colour change: ΔE CIELAB formula according toRead More …
D5 Creation